Gas Fireplace Log Instructions. A gas log fireplace insert is one that is inserted into an existing fireplace. A step by step guideline on how to install illusions gas log fire.
Adding a gas log lighter to a fireplace is one of the most popular upgrades for fireplace owners. All aspects of pilot operation and receiver installation
24 In Split Oak Vented Gas Log Set Dual Burner Realistic
Although many gas fireplaces have a knob or ignitor switch to light the fire, some older gas fireplaces units have a metal key that is inserted into a keyhole which turns on the gas flow to start the fire. Avoid any drafts that alter burner flame patterns.
Gas Fireplace Log Instructions
Do not use a natural gas set for a propane or a propane set for natural gas.Do not use abrasive cleaners.Each fireplace and insert has a rating plate which contains your model number and serial number.Find your heatilator product installation or owner’s manual.
Finding the model of your fireplace, stove or insert.For safe installation and operation of your gas fireplace please note the following:For safe operation, glass doors must be closed.Gas and wood burning fireplaces have a rating plate in the control compartment area, under the smoke shield or on the firebox side column.
Gas fireplace pilot light the installer should do the initial lighting of the pilot light during installation.Gas log burners and decorative appliances models:Gently push in the gas control knob and turn it clockwise to “off” 4.Here we explain the facts about adding a gas log lighter to your wood burning fireplace, so you can have peace of mind in adding this easy home feature.
If piezo ignitor does not light the pilot, refer to your manual for match lighting instructions.If the knob is not in the off position, turn it so that it is.If you do not smell gas, you can proceed to lighting.If you're converting an existing wood burning fireplace into a gas log fireplace, and you want to know what size log set will fit, just take the following measurements on your fireplace.
In order to gain minimum gas insert fireplace opening requirement, if the fireIt also provides a cleaner burning fireplace that is easier to maintain and have in your home.It is recommended that the jetmaster gas log be placed in a properly installed jetmaster convector firebox in order to ensure an adequate draught and greater efficiency.the jetmaster open fire is an approved open fire to burn wood.It really does save you time so you can spend more time just enjoying the fire.
Jetmaster gas logs are fuel effect appliances intended for use in a fireplace suitable for the burning of wood.Leave this manual with the appliance.Leave your house to call your gas provider for proper instructions, or, if your gas provider is unavailable, the fire department.Look for a knob on your control panel with the words on, off, and pilot on it.
Measure the distance between the two points at (a), (b), (c), and (d) as depicted to the left.Most gas log sets will need to have the gas coming from the right rear side of the burner system, but this can vary from appliance to appliance.Once you begin the operation of the gas fireplace, you can run the pilot light in one.Open the bottom louver assembly.
Remove the gas logs from the fireplace and take them outside for cleaning.Retain this manual for future reference.Set the regulator switch to “off” 3.The good news is they can be swapped out without replacing the whole fireplace.
Then, let your fireplace sit for at least 5 minutes, allowing any excess or lingering gas to clear out.This appliance may be installed in an aftermarket permanently located,.This eliminated the need for wood or wood pellets as fuel for the fireplace.This gas log set is equipped with an ignition device (piezo) which automatically lights the pilot.
This type of fireplace uses gas that when ignited provides heat in the fireplace.To determine the largest set that will fit in a fireplace, the width.Turn gas control knob clockwise to the off position and turn on/off switch to off position.Turn the control knob to the off position for at least 5 minutes.
Use a soft paintbrush to brush away any dirt or debris from the logs.Using a substitute glass will void all product warranties.Wait 10 minutes or so for any gas to clear out.When purging the gas line, the glass front must be removed.
Posting Komentar
Posting Komentar